GALEP-5 is a universal programmer for devices of the following types: EPROM, EEPROM, FLASH memory, serial EEPROM, NV-RAM, LPC, FPGA, PLD, EPLD, GAL, PALCE, PIC, Microcontroller (MCU). More than 62,000 devices algorithms are currently supported (GALEP-5 device list). Additionally, GALEP's JTAG player can program SVF/JAM data into all existing and future devices that have a JTAG port.
Ultra-Compact, USB-Powered Design
The GALEP-5 device programmer fits into your jacket pocket and weighs less than 200g, compared to 3..4 lbs of bulky competitor products. It is completely powered through the USB bus and does normally not require any additional
power supply. Only when the programmable device consumes more than 500 mA, which is the case for few old NMOS devices and some microcontrollers, the included power adapter or batteries (6xAAA) can be used.
Extremely Fast Programming
GALEP-5 is uncompromisingly designed for speed. An internal 200 MIPS ARM-9 processor handles the data transfer; an 50,000 gates FPGA (user-programmable logic) controls the pin drivers and accelerates programming algorithms by setting up device-dependent state machines and UARTs. The hardware acceleration makes GALEP-5 one of the fastest device programmers on the market today. For instance, a MB91F467 Fujitsu Microcontroller (8 Mb) needs only 19 seconds for a serial program/verify cycle. A 256 Mb NOR Flash (28F256P30) is programmed and verified in 170 seconds. The internal 64 MByte RAM serves as data storage and allows to transfer data only once for programming multiple devices.
48 High-Speed pin drivers
A custom-designed universal pin driver IC guarantees optimal signal quality at the output pins, and allows the small size and low power consumption of all GALEP chip programmers. Each of the 48 pins can generate the following signals:
- Logical high between 1.2V .. 5.0V
- Logical input, threshold 0.5V … 5.0V
- Three programming voltages between 1.3V .. 25.0V
- Three switchable resistors for pullup and pulldown
- Adjustable clock rate
The switching regulators for the programming voltages are controlled by D/A converters in 100 mV steps. Further D/A converters are used to control the logic levels and the input threshold. For maximum protection of the programmable device, all voltages are permanently monitored by an independent circuit.
In System Programming
for In-System Programming (ISP) can be taken from a separately
available ISP adapter or directly from the 48-pin ZIF socket.
The help system provides information about the wiring of the
target system for all supported components. With the multiboard adapter, GALEP-5 can connect up to 32 MCU boards and program them simultaneously!
The software runs under Windows 95, 98, ME, NT4, 2000, XP, Vista, 7, 8, 10, and Linux. Besides basic functions such as erase, read,
program and compare, split and shuffle, it features easy-to-use configuration options for any special functions required by the selected device. The software supports all common file formats, such as binary, Hex, JEDEC, and JTAG. Mass production is supported by providing statistics functions and serial number generation.
JTAG Support: Delete, program and verify components with JTAG interface (joint test action group, IEEE Std. 1149.1 ). The following formats are supported: SVF-Script in XSVF(Xilinx) format; JAM byte code player (ALTERA).
Batch mode: Run GALEP-5 from the command line, or implement GALEP commands in your own production software. The programmer can be completely controlled by a set of powerful batch commands.
Updates: The software is permanently improved for supporting new components (device list).
With GALEP-5 you can debug all Microcontrollers with JTAG interface that are supported by the OpenOCD (On Chip Debugger) software - ARM7, ARM9, XScale, and Cortex-M3 MCUs. The chip to debug is simply put into GALEP's programming socket or connected with GALEP through a cable or ISP adapter (please find details in the OpenOCD documentation). Additionally you can easily define test algorithms for in circuit testing of complete circuit boards (Boundary Scan) for small series production. This way your GALEP-5 becomes a complete development, test and production system!
to each function, GALEP checks the power consumption, correct
positioning, and the contacts of all pins of the selected component.
This effectively prevents any accidental damage to the component or the programmer.
programs components in DIL sockets up to 48 Pins between
300 … 600 MIL (ca. 7,5 … 16 mm) wide without additional
Universal socket adapters are available for all components with
up to 48 pins. Only one adapter per socket is required; few adapters
= small system costs!
Adapters for components with more than 48 pins are also available.
Because the pin number of the programming device is smaller than
the pin number of the components, such adapters are specialized.
If you have to program components with a high pin number frequently,
a GALEP-5D (with up to 240 pin drivers) might be the more effective solution.
adapters can be used with GALEP-5. Adapters for the following sockets are available: SOIC, SOP, TSOP, SSOP, TSSOP, PLCC, QFP, TQFP, MLF.
format: ca. 80 x 115 x 33 mm (+7mm socket)
ca. 185 g
socket with 48 universal pin drivers
low-voltage components down to 1.3V
USB 2.0 high-speed
AC adapter plus battery compartment
for high-power devices
ARM-9 RISC processor, 64 MB RAM, 8 MB Flash
gates, 64Kb RAM)
linear voltage regulators for internal power supply
switching regulators for programming voltages
linear voltage regulators for logic levels and input threshold
for internal voltage monitoring
D/A converter, 16-channel A/D converter
Linux 2.6 inside
manual and software
Windows 2000 / XP / Vista / Win 7 / Win 8 / Win 10 / Linux
or USB 2.0 port
GALEP-5 Kit: ......................................... EUR 499.- /
GALEP-5 Kit with new for old discount: EUR 399.- / US$ 499.-
Prices don't include VAT and shipping. Warranty: 24 Months. CE and RoHS certified.